MEC&F Expert Engineers

Monday, March 8, 2021

C&O INVESTIGATIONS: LIGHTNING OR POWER SURGE DAMAGE TO HVAC AND OTHER EQUIPMENT, Part II

 

This time of the year we are often being asked to provide forensic investigations regarding the cause and origin of damages to HVAC system or individual component(s).  This is Part II of the HVAC damage claims blog; it addresses the typical causes of damage associated with HVAC systems.  Claims dealing with theft of the copper wiring of these units as well as excessive replacement costs are certainly on the rise. 

There are a number of components in an HVAC system that can fail, including the compressor, the condenser fan, the air handler blower, the refrigerant copper piping, the air filter, the evaporator coils, and so on.  When it comes to damages caused by an insured peril such as lightning, the most common damage we have seen is damage to the electronics and the air compressor.

Typical Problems

We often see problems associated with contamination of the refrigerant, especially the mixing of the R22 with the R410 refrigerants.  Other problems include, but are not limited to, corroded or loose terminal connections, high refrigerant pressure, refrigerant leaks, failed electronic controls and sensors, worn out internal components of the compressor, bad electric and mechanical installation, failed fans, a short to ground in the fan motor or a short to ground in the fan motor wires that lead to the motor, and so on.  Over time, low refrigerant levels can cause overheating and premature failure of the compressor, often requiring complete replacement of the compressor or the entire condensing unit.  The electronic controls and sensor that cause the air conditioner, fan and condenser to kick off and on properly, are often the first components to go.  Sometimes these sensors are merely knocked out of position causing the air conditioner to cycle constantly or behave erratically.

The Refrigerant Charge Problem Is Widespread

In a recent study, for Arizona Public Service, heat pump or air conditioner systems were tested for their refrigerant level.  The study results are indicated in the graph below.  Only eighteen (18%) percent of all the units were properly charged (green bar).  Seventy-eight (78%) percent of the units were under charged (yellow-red bars).  While four (4%) percent were over charged (red).  These results are consistent with previous industry research, from new home construction studies in California, Long Island and elsewhere.

 



The heart of the HVAC unit is the compressor, which is cooled by the refrigerant.  Over time, low refrigerant levels can cause overheating and premature failure of the compressor, often requiring complete replacement of the compressor or the entire condensing unit.

__________________________________________________________________

Did you know that most air conditioning compressor failures are caused by loss of lubricant and/or refrigerant?  Older systems, especially before 2006 were connected with mechanical flare fittings that can rattle loose due to vibration of the system with leaks resulting.  Most new units are welded at their connection points, reducing the chance for leaks to occur.

__________________________________________________________________

Misconceptions about Cause of Failure

During the first step of our investigation we interview the insured and any witnesses to the damage.  Witnesses typically tell us that they heard a sound and that they saw sparks and smoke coming out of the equipment; at other times they state that the compressor worked just before the storm and then it stopped working.  Even the HVAC repair technicians many times state that the oil was black or that the insulation was burned or the terminal was blown.  They then assume that a lightning hit the unit without performing an investigation into the actual mode of failure.

An electric failure does not necessarily cause mechanical failure of the equipment.  On the other hand, a mechanical failure (a broken valve, worn bearing, blocked coils, rusty terminals, etc.) may have been the cause of an electrical failure.  Thus, if the motor windings are electrically sound, then the compressor was not damaged by a surge voltage or lightning stroke.

The often heard statement “the blackened acidic oil indicates the motor was damaged by a lightning stroke” is also false.  The compressor oil will blacken and form an acid only when the oil is exposed to excessive heat for an extended period of time.  Overheating of the motor-compressor unit is the most frequent symptom of system problems.  The heating and charring of motor winding insulation causes a chemical breakdown that combines with the oil.  This will then blacken the oil and form an acid.  When a motor fails as a result of a surge voltage or lightning stroke, the oil is normally in a like-new condition.  A surge voltage or lightning strike occurs in an extremely short period of time which does not allow enough time for the oil to blacken and turn acidic.  Thus, if the refrigerant oil is burnt or acidic there is a good chance that the damage is not lightning/power surge related.  It should also be noted that burnt or acidic refrigerant oil does not require the replacement of the entire system as is commonly stated.

Another misconception about lightning is that it can damage a motor-compressor unit even if the equipment is turned off during a storm.  If a surge voltage or lightning stroke has enough voltage to gap the open contacts on the main contactor, then there will be damage to various other components in the air-conditioner and possibly to the building’s entire electrical system.  Therefore, the insulation melts and could possibly start a fire before the air-conditioner is damaged.

Dirty Condenser Coils or Fan will lead to Premature Failure

Air Conditioner or Heat Pump Condenser Coils, if are not cleaned regularly, can get plugged up by dust, dirt, pollen, grass, and other foreign debris.  See Figure 1.



Figure 1.  Dirty condenser coil that led to seizure of the fan and compressor.  Power surge was not the cause of this loss.  It was caused by lack of regular maintenance.

Sometimes these obstructions to the flow of air are not seen by just looking at the condenser; the interior of the condenser must be opened up and examined very carefully.  Problems caused by this condition:

·       Unit loses the ability to remove heat from the system.

·       Results in higher pressures in the condenser which causes the compressor to pull higher amps.

·       Higher amp draw means more stress on the motors, overheating of the motor, and potentially leading to premature failure.

·       At other times we observe that the outdoor fan is not running; this could be caused by a damaged capacitor, bent fan blades of fan motor failure.  Wear & tear is the most common reason for a failing exterior fan.  Another common reason for failure is the accumulation of dirt and debris on the fan blades, and loose or corroded terminals and contactors, i.e., lack of regular maintenance.

·       Lack of adequate air flow through the condenser causes the condenser fan motor to run hotter than normal and the compressor to run hotter because of the higher load conditions; all these lead to premature failure of these components.  Most of the time, the HVAC tech will state that power surge caused the damage to the equipment.

Loose or Corroded Terminal Problems will also lead to Failure

Problems with loose or rusted terminal pins are also a common cause of AC compressor failure.   See Figure 2.  If the terminal pins are loose or “blown” on a compressor, then the compressor will need to be replaced.  However, pin failure does not indicate damage by a surge voltage or lightning stroke.  The most likely cause of a burned electrical terminal on a compressor is a loose electrical connection.  This loose connection causes a buildup of heat and results in a burned terminal. 

Rusty terminal connections also create the same low voltage condition as loose terminal pins.  When a low voltage condition occurs, the motor will slowly fail.  This low voltage condition also causes even higher heat to develop at the terminal pin connection causing even greater rust.  This results in additional disintegration of the connection and causes low voltage to be supplied to the motor which eventually causes the motor to fail or the terminal pin(s) to become dislodged.

________________________________________________________________________

Did you know that repeat compressor failures are usually due to system ­contamination (sludge or metallic particles from a previous compressor failure)?

________________________________________________________________________

It is possible to have damaged pins due a lightning strike, but this is limited to situations where the lighting strike damage is severe.  In these cases there is a lot of other evidence of a lightning strike.  The condenser fan motor or other electrical components of the system will have been damaged.  The wires are burnt and there is evidence of arc marks to the cabinet where the wires run close to the cabinet.  There is also considerable damage to other motors and appliances as well as to the electric panel.

 




Figure 2.  Burned compressor plug due to defective (loose) connection to the compressor.  Initially the HVAC techs claimed that this was caused by power surge.  However, there was no other evidence (storms, lightning, utility reports, etc.) to support that claim.  A power surge big enough to do that damage to the compressor plug would have damaged the whole control section, capacitor, contactor and most of the wiring.  No such evidence was observed during our investigation.

In case of any equipment or HVAC compressor-related problem, it is important to identify the root cause, without jumping to the conclusion that the equipment was damaged by lightning or power surge.  If the compressor is replaced without attending to the root cause, the replaced compressor surely will also fail.

Metropolitan Engineering, Consulting & Forensics (MECF)

Providing Competent, Expert and Objective Investigative Engineering and Consulting Services

P.O. Box 520

Tenafly, NJ 07670-0520

Tel: (201)293-6064

E-mail: metroforensics@gmail.com

Web pages:  https://sites.google.com/site/metropolitanenvironmental/

To unsubscribe from future technical blogs and announcements, please reply to this email with the word “unsubscribe” in the subject line.

 

Metropolitan appreciates your business.

Feel free to recommend our services to your friends and colleagues.

We know you need to process damage claims quickly and knowing the facts is now faster than ever – within 24 hours of site visit.  Our Pegasos Forensic Investigation Services (PFIS) feature:

·       Expert Forensic Investigators on-site.

·       Defensible, Readable, Conclusive Reports.

·       Fixed-Prices starting at $499 per chimney or roof inspection (volume discounts are also available).  Flood loss assessments start at $999.0.  HVAC equipment only inspections start at $299 for local (within one hour one-way drive) assignments.

·       10-State Coverage Area.

Metropolitan has extensive experience assisting in the evaluation of environmental factors. Our Certified Industrial Hygienists and Registered Professional Engineers have performed IAQ testing, mold testing, Chinese drywall corrosion investigations, water source evaluation and remediation design and oversight.

We perform Property Condition Assessments, Indoor Air Quality Evaluations and Environmental Site Assessments, including Indoor Air Quality

Saturday, March 6, 2021

THOUSANDS MORE SPEEDING DRIVERS DIE AND KILL OTHER DRIVERS DURING THE PANDEMIC




Early Estimate of Motor Vehicle Traffic Fatalities for the First 9 Months (Jan–Sep) of 2020

A statistical projection of traffic fatalities for the first 9 months of 2020 shows that an estimated 28,190 people died in motor vehicle traffic crashes. This represents an increase of about 4.6 percent as compared to 26,941 fatalities reported to have occurred in the first 9 months of 2019, as shown in Table 1. Preliminary data reported by the Federal Highway Administration (FHWA) shows that vehicle miles traveled (VMT) in the first 9 months of 2020 decreased by about 355.5 billion miles, or about a 14.5-percent decrease. Also shown in Table 1 are the fatality rates per 100 million VMT, by quarter. The fatality rate for the first 9 months of 2020 increased to 1.35 fatalities per 100 million VMT, up from the 1.10 fatalities per 100 million VMT in the first 9 months of 2019. The counts for 2019 and 2020 and the ensuing per-centage change from 2019 to 2020 will be further revised as the final FARS files for 2019 are available next year. These estimates may be further refined when the projections for the whole of 2020 are released in late April 2021

The number of people killed on the nation’s highways rose 4.6% in the first nine months of 2020 despite coronavirus lockdowns that curtailed driving early in the year.

The National Highway Traffic Safety Administration estimates that 28,190 people died in traffic crashes from January through September of last year, up from 26,941 in the same period of 2019. Final statistics for the full year won’t come out until fall.


Authorities blamed the increase on risky driving behavior that developed when there were few vehicles on the road early in the pandemic.

“Preliminary data tells us that during the national health emergency, fewer Americans drove, but those who did took more risks and had more fatal crashes,” the safety agency said in a letter addressed to the nation’s drivers.

Traffic deaths rose 0.6% during the first-quarter of 2020, but they fell 1.1% in the second quarter as coronavirus lockdowns restricted movement. Fatalities spiked 13.1% from July through September, the agency said.

“We think the big culprit is speeding,” said Jonathan Adkins, executive director of the Governors Highway Safety Association. Early in the pandemic, drivers found open roads and drove faster. The behavior continued even as traffic volumes recovered, Adkins said.

“A big factor here is the lack of enforcement. We are hearing from many states that traffic stops have declined during COVID-19. Drivers feel like they can speed and get away with it,” he said.

NHTSA said recent reports show a 22% increase in vehicle speeds in several metropolitan areas over pre-pandemic numbers. Also, a study found that 65% of drivers treated at trauma centers who were hurt in serious crashes had drugs or alcohol in their systems last year. It was 50.6% before the pandemic, NHTSA said. The agency also said fewer people are wearing seat belts.

The agency is telling people not to drive under the influence of drugs or alcohol, to wear seat belts and to reduce their speeds in order to stay safe. It also says people should make sure their children are in the proper car seat for their size.


 

1,4 DIOXANE: FATE AND TRANSPORT AND TREATMENT TECHNOLOGIES

EPA evaluated 1,4-dioxane under the amended Toxic Substances Control Act (TSCA) and completed the final risk evaluation in December 2020. EPA will now begin the process of developing ways to address the unreasonable risks identified and has one year to propose and take public comments on any risk management actions.

Uses of 1,4-Dioxane

1,4-dioxane is currently used as a solvent in a variety of commercial and industrial applications such as in the manufacture of other chemicals, a processing aid, functional fluid, a laboratory chemical, in adhesives and sealants, in spray polyurethane foam, in printing inks, and as a dry film lubricant. 1,4-dioxane may be found as a contaminant in consumer products such as soaps and detergents. Information from the 2016 Chemical Data Reporting (CDR) for 1,4-dioxane indicates reported production volume in more than 1.1 million lbs/year (manufacture and import).


Risk Evaluation of 1,4-dioxane under Amended TSCA

In December 2020, EPA released the final risk evaluation for 1,4-dioxane. The final risk evaluation shows that there are unreasonable risks to workers and occupational non-users from 13 conditions of use. EPA found no unreasonable risks to the environment, consumers, bystanders, or the general population. As with any chemical product, EPA strongly recommends that users carefully follow all instructions on the product’s label.

In June 2019, EPA released the draft risk evaluation for 1,4-dioxane for public comment and peer review. In November 2020, EPA released a supplemental analysis to the draft risk evaluation which includes eight consumer uses where 1,4-dioxane is present as a byproduct, meaning when 1,4-dioxane is created from the breakdown of other chemicals. The supplemental analysis also assesses exposure to the general population from 1,4-dioxane in surface water.

In June 2017, EPA released the scope document for 1,4-dioxane which includes the hazards, exposures, conditions of use, and the potentially exposed or susceptible subpopulations EPA expects to consider in its risk evaluation of 1,4-dioxane conducted pursuant to TSCA section 6(b). In June 2018, EPA released the problem formulation for 1,4-dioxane which refined the scope of the 1,4-dioxane risk evaluation by clarifying the chemical uses that EPA expected to evaluate and describing how EPA expected to conduct the evaluation. 


Treatment Technologies for 1,4-Dioxane

1,4-Dioxane is a solvent stabilizer frequently found at contaminated sites where methyl chloroform (1,1,1-trichloroethane) was used for degreasing.  This report profiles the occurrence and properties of 1,4­dioxane and provides a summary of the available remedial technologies. The information presented should prove useful to project managers and other regulatory officials who oversee cleanup of contaminated groundwater, particularly where chlorinated solvents are the principal contaminant. Consultants, including hydrogeologists, remediation engineers, and modelers, should also find this report useful, as should water utility operators and regulators. In recent years, the regulated community has become increasingly aware that 1,4-dioxane is likely to be present at sites where methyl chloroform is a contaminant.

Although 1,4-dioxane has been a constituent of methyl chloroform wastes for decades, recent improvements to analytical methods allowed its detection in the parts per billion range beginning in 1997. Analysis of 1,4-dioxane often must be specifically requested. The common practice of analyzing by a limited list of available methods for regulatory compliance has precluded detection of 1,4-dioxane. The properties that made 1,4-dioxane difficult to analyze in the past also make it difficult to treat. For example, 1,4-dioxane is fully miscible in water.

As a hydrophilic contaminant, it is not, therefore, amenable to the conventional ex situ treatment technologies used for chlorinated solvents. Successful remedial technologies must take into account the challenging chemical and physical properties unique to 1,4-dioxane. This report profiles technologies that have been shown to successfully remove or eliminate 1,4-dioxane and examines other technologies currently under development. 1,4-Dioxane is among the most mobile organic contaminants in the saturated zone. As a result, it may be found farther downgradient than the leading edge of a solvent plume.

The combination of a wider spatial occurrence and different requirements for treatment technologies make 1,4-dioxane a potentially problematic contaminant, particularly if it is discovered after site characterization and remedial design have already been completed. In some cases, discovery of 1,4-dioxane has necessitated expanded monitoring networks, larger capture zones, and the addition of new treatment technologies to the treatment train.

 

TREATMENT OF MEDIA CONTAINING DIOXANE

The physical and chemical properties of dioxane create challenges for removing this compound from water. Dioxane is well suited to removal by groundwater extraction because of its high solubility and low degree of partitioning to organic matter in soil.

However, the relatively low Henry’s Law constant of dioxane makes technologies such as air stripping generally ineffective in treating the chemical in water. Its low adsorptive capacity also limits the effectiveness of treatment by granular activated carbon (GAC), although one full-scale GAC application was identified. Bench-scale studies indicate that biodegradation of dioxane is possible, but information on field applications of this technology is limited (Dr. Basilis Stephanatos and others 2001). Technologies that are effective for treating chlorinated solvents are often ineffective for treating dioxane because the properties of dioxane differ from those of chlorinated solvents.

To date, the number and types of technologies available to treat dioxane are limited; however, research is under way to test and evaluate additional treatment technologies for this contaminant.

To date we are familiar with three technologies that have been used to treat dioxane at the pilot and full scale levels:

•Advanced oxidation (ex situ)

•Adsorption (GAC) (ex situ)

•Bioremediation

 

As discussed previously, dioxane in soil tends to readily partition to groundwater and does not sorb to soil particles. Therefore, groundwater is the primary medium of concern for this contaminant.







EPA Releases Testing Data Showing PFAS Contamination from Fluorinated Containers

 




EPA Releases Testing Data Showing PFAS Contamination from Fluorinated Containers


WASHINGTON (March 5, 2021) — As the U.S. Environmental Protection Agency (EPA) pursues its mission to protect human health and the environment, addressing risks related to PFAS is a priority. To this end, EPA is making available new testing data related to PFAS found in fluorinated containers in which a mosquito control product was packaged and sold. EPA is also announcing its planned next steps to further characterize and address this potential source of contamination.

“Advancing science and taking action to reduce the health risks associated with PFAS go hand-in-hand,” said Acting Assistant Administrator for the Office of Chemical Safety and Pollution Prevention Michal Freedhoff. “The Biden-Harris Administration’s focus on developing and using the best available science will guide our decision-making, strengthen our work with stakeholders, and lead to pragmatic solutions that advance our efforts to address PFAS contamination and protect human health.”

Since first becoming aware of the PFAS contamination issue in September 2020 through citizen science testing of a pesticide product, EPA has been working to investigate the source of the contamination. In December 2020, EPA studied the fluorinated HDPE containers used to store and transport the product and preliminarily determined the fluorination process used may be the source of PFAS contamination.

In January 2021, EPA continued its testing which showed the PFAS were most likely formed from a chemical reaction during the container fluorination process which then leached into the pesticide product. After completing a robust quality assurance and quality control process, EPA can confirm that it has detected eight different PFAS from the fluorinated HDPE containers, with levels ranging from 20-50 parts per billion.

While EPA is early in its investigation, the agency will use all available regulatory and non-regulatory tools to determine the scope of this emerging issue and its potential impact on human health and the environment. It is important to note that although these types of products should not be a source of PFAS, the data indicates that the amount of PFAS that has entered the environment from the contamination in the containers the agency tested is extremely small. The agency is also committed to coordinating with the affected entities involved and their supply and distribution chains, pesticide users, the pesticide and packaging industry, and its federal, state, and tribal partners as it works through this complex health and environmental issue.

Building on the agency’s initial actions announced in January 2021, EPA initiated a series of steps to tackle this issue including:

  • On Jan. 13, 2021, to minimize risks to human health and the environment, EPA asked states with existing stock of the mosquito product distributed in fluorinated HDPE containers to discontinue use and hold that inventory until its final disposition is determined. The pesticide manufacturer has also notified all its customers regarding management of the product, voluntarily stopped shipments of all products in fluorinated HDPE containers, and is now using non-fluorinated containers.
  • On Jan. 14, 2021, EPA issued a TSCA subpoena to the company that fluorinated the containers supplied to the manufacturer of the pesticide in which PFAS was discovered to learn more about the fluorination process used on the HDPE containers. 
  • EPA is aware that many companies are using fluorinated HDPE containers to store and distribute pesticide and other products. EPA is actively working with the Food and Drug Administration, the U.S. Department of Agriculture, and industry and trade organizations to raise awareness of this emerging issue and discuss expectations of product stewardship. For example, EPA is coordinating with the Ag Container Recycling Council, the American Chemistry Council, Crop Life America, the Household & Commercial Products Association, and the National Pest Management Association.
  • The agency is also testing different brands of fluorinated containers to determine whether they contain and/or leach PFAS, and if so, learn the conditions affecting leaching. EPA will present these findings as expeditiously as possible.
  • The agency is encouraging the pesticide industry to explore alternative packaging options, like steel drums or non-fluorinated HDPE.
To view the data and learn more, visit: https://www.epa.gov/pesticides/pfas-packaging