THIS SUDDEN DEEP FREEZE WILL CAUSE PROPERTY DAMAGE FROM NON-WINTERIZED PIPE BURSTS EVEN IN SOUTHERN HOMES
REGIONAL
DIFFERENCES - WHY PIPES BURST IN SOUTHERN CLIMATES
Surprisingly,
ice forming in a pipe does not typically cause a break where the ice blockage
occurs. It’s not the radial expansion
of ice against the wall of the pipe that causes the break. Rather, following a
complete ice blockage in a pipe, continued freezing and expansion inside the
pipe causes water pressure to increase downstream -- between the ice blockage
and a closed faucet at the end. It’s this increase in water pressure that leads
to pipe failure. Usually the pipe bursts where little or no ice has formed.
Upstream from the ice blockage the water can always retreat back towards its
source, so there is no pressure build-up to cause a break. Water has to freeze
for ice blockages to occur. Pipes that are adequately protected along their
entire length by placement within the building’s insulation, insulation on the
pipe itself, or heating, are safe.
Generally,
houses in northern climates are built with the water pipes located on the
inside of the building insulation, which protects the pipes from subfreezing
weather. However, extremely cold weather and holes in the building that allow
a flow of cold air to come into contact with pipes can lead to freezing and
bursting.
Water
pipes in houses in southern climates often are more vulnerable to winter cold
spells. The pipes are more likely to be located in unprotected areas outside of
the building insulation, and homeowners tend to be less aware of freezing
problems, which may occur only once or twice a season.
Pipes
in attics, crawl spaces and outside walls are all vulnerable to freezing,
especially if there are cracks or openings that allow cold, outside air to flow
across the pipes. Research at the University of Illinois has shown that “wind chill,”
the cooling effect of air and wind that causes the human body to lose heat, can
play a major role in accelerating ice blockage, and thus bursting, in water
pipes.
Holes
in an outside wall where television, cable or telephone lines enter can provide
access for cold air to reach pipes. The size of pipes and their composition
(e.g., copper or PVC) have some bearing on how fast ice forms, but they are
relatively minor factors in pipe bursting compared with the absence of heat,
pipe insulation and exposure to a flow of subfreezing air.
When
is it Cold Enough to Freeze?
When
should homeowners be alert to the danger of freezing pipes? That depends, but
in southern states and other areas where freezing weather is the exception
rather than the rule (and where houses often do not provide adequate built-in
protection), the “temperature alert threshold” is 20 degrees F.
This
threshold is based upon research conducted by the Building Research Council at
the University of Illinois. Field tests of residential water systems subjected
to winter temperatures demonstrated that, for un-insulated pipes installed in
an unconditioned attic, the onset of freezing occurred when the outside
temperature fell to 20 degrees F or below.
This
finding was supported by a survey of 71 plumbers practicing in southern
states, in which the consensus was that burst-pipe problems began to appear
when temperatures fell into the teens. However, freezing incidents can occur
when the temperature remains above 20 degrees F. Pipes exposed to cold air
(especially flowing air, as on a windy day) because of cracks in an outside
wall or lack of insulation are vulnerable to freezing at temperatures above the
threshold. However, the 20 degrees F “temperature alert threshold” should
address the majority of potential burst-pipe incidents in southern states.
MITIGATING
THE PROBLEM
Water
freezes when heat in the water is transferred to subfreezing air. The best way
to keep water in pipes from freezing is to slow or stop this transfer of heat.
Ideally,
it is best not to expose water pipes to subfreezing temperatures, by placing
them only in heated spaces and keeping them out of attics, crawl spaces and
vulnerable outside walls. In new construction, proper placement can be designed
into the building.
In
existing houses, a plumber may be able to re route at-risk pipes to protected
areas, although this may not be a practical solution. If the latter is the
case, vulnerable pipes that are accessible should be fitted with insulation
sleeves or wrapping (which slows the heat transfer), the more insulation the
better. It is important not to leave gaps that expose the pipe to cold air.
Hardware stores and home centers carry the necessary materials, usually in foam
rubber or fiberglass sleeves. Better yet, plumbing supply stores and insulation
dealers carry pipe sleeves that feature extra-thick insulation, as much as 1 or
2 inches thick. The added protection is worth the extra cost.
Cracks
and holes in outside walls and foundations near water pipes should be sealed
with caulking to keep cold wind away from the pipes. Kitchen and bathroom
cabinets can keep warm inside air from reaching pipes under sinks and in adjacent
outside walls. It’s a good idea to keep cabinet doors open during cold spells
to let the warm air circulate around the pipes. Electric heating tapes and
cables are available to run along pipes to keep the water from freezing. These
must be used with extreme caution; follow the manufacturer’s instructions
carefully to avoid the risk of fire, and check to make sure the product
conforms to UL 2049. Tapes and cables with a built-in thermostat will turn
heat on when needed. Tapes without a thermostat have to be plugged in each time
heat is needed, and may be forgotten.
LETTING
THE WATER RUN
Letting
a faucet drip during extreme cold weather can prevent a pipe from bursting.
It’s not that a small flow of water prevents freezing; this helps, but water
can freeze even with a slow flow.
Rather,
opening a faucet will provide relief from the excessive pressure that builds
between the faucet and the ice blockage when freezing occurs. If there is no
excessive water pressure, there is no burst pipe, even if the water inside the
pipe freezes.
A
dripping faucet wastes some water, so only pipes vulnerable to freezing (ones
that run through an unheated or unprotected space) should be left with the
water flowing. The drip can be very slight. Even the slowest drip at normal
pressure will provide pressure relief when needed. Where both hot and cold
lines serve a spigot, make sure each one contributes to the drip, since both
are subjected to freezing. If the dripping stops, leave the faucet(s) open,
since a pipe may have frozen and will still need pressure relief.
IF YOU SUSPECT A FROZEN PIPE
If
you open a faucet and no water comes out, don’t take any chances. Call a
plumber. If a water pipe bursts, turn off the water at the main shut-off valve
(usually at the water meter or where the main line enters the house); leave the
faucet(s) open until repairs are completed. Don’t try to thaw a frozen pipe
with an open flame; as this will damage the pipe and may even start a building
fire. You might be able to thaw a pipe with a hand-held hair dryer. Slowly
apply heat, starting close to the faucet end of the pipe, with the faucet open.
Work toward the coldest section. Don’t use electrical appliances while standing
in water; you could get electrocuted.
GOING ON A TRIP
When
away from the house for an extended period during the winter, be careful how
much you lower the heat. A lower temperature may save on the heating bill, but
there could be a disaster if a cold spell strikes and pipes that normally would
be safe, freeze and burst.
A
solution is to drain the water system. This is the best safeguard. With no
water in the pipes, there is no freezing. This remedy should be considered even
when the homeowner is not leaving but is concerned about a serious overnight
freeze.
To
drain the system, shut off the main valve and turn on every water fixture (both
hot and cold lines) until water stops running. It’s not necessary to leave the
fixtures open, since the system is filled mostly with air at that point and not
subject to freezing. When returning to the house, turn on the main valve and
let each fixture run until the pipes are full again.

