CAUSE & ORIGIN INVESTIGATIONS: HOT WATER TANK AND WASHING MACHINE FAILURES
https://sites.google.com/site/metropolitanforensics/cause-origin-investigations-hot-water-tank-and-washing-machine-failures
According to
nationwide analyses by insurers, one out of every ten water-damage claims can
be traced back to a failed hot water tank or washing machine. These studies revealed that water heaters or
washing machines fail most often when they develop a slow leak or burst. Most of the time the failure will occur once
the water heater has reached its life expectancy, typically suggested by the
warranty period of the manufacturer. If
the hot water tank reaches its warranty period, then the insured must monitor
the equipment very carefully for signs of leaks or corrosion. The washing machines fail at least 55 percent
of the time due a bursting hose.
Figure 1: Failed hot water tank. Note the significant corrosion of the
exterior shell of the tank. It should
have been replaced several years ago prior to the failure.
The good
news is that there are plenty of stress signs that these equipment give prior
to the failure. Proper maintenance,
including inspecting the water heater’s anode rod and flushing sediment from
the tank, can delay the need to replace a water heater.
Figure 2.
Another failed tank that resulted in significant property damage. The property loss could have been prevented,
should the insured have taken an earlier action to properly maintain, repair or
replace the tank, because the first signs of rust appeared well before the tank
failed.
Most water
heater storage tanks are constructed of steel and contain an internal glass
lining to protect the storage tank from corrosion. The glass lining often has imperfections that
develop during manufacturing or while handling the water heater during
installation. These imperfections allow water to penetrate the glass lining and
eventually lead to corrosion of the exterior shell of the storage tank. If the corrosion persists, the water tank will
begin to leak and eventually burst. Even
the tanks that have plastic linings can fail because the O-rings or gaskets (i.e.,
the joints) can fail over time.
It is also
important to note that the sacrificial anodes that manufacturers place in the
tanks have a limited life. Once this metal rod has been “consumed” or
“sacrificed”, it can no longer protect the steel tank. The anode rod should be inspected once every
two years and at least annually once the warranty has expired. Acidic water (low pH) or the use of a water
softener that adds sodium to the water making it more corrosive can accelerate
the corrosion of the anode rod.
Therefore, it is strongly recommended to more frequently inspect the
anode under these conditions.
Preventive
water heater maintenance should also include removing sediment by flushing the
tank every six months or more frequently if well water is being used that has
lots of iron in it. Areas with hard
water, such as the Northeast, will also see faster accumulation of deposits
inside the tanks. As the layer of
sediment thickens, it can act as a barrier to the operation of the anode. In gas water heaters, it can also cause the
water heater flame to work harder to heat the water, resulting in early
deterioration and deformity at the base of the water heater.
The pressure
relief valve is another weak area that requires carefully monitoring, at least
once a year. At least every five years
the valve should be replaced. If the
relief valve is not working properly, heat and pressure can build up and cause
the water tank to explode or to prematurely fail. See Figures 3 and 4 for a tank that failed
because the relief valve was not functioning due to lack of maintenance.
Figure 3.
Failed hot water tank. Due to
lack of sediment removal over ten years or so, and due to clogged pressure
relief valve, the tank finally gave in, causing very significant property
damage.
Figure 4.
Property damage in excess of $100K caused by the failure of the tank
depicted in Figure 3.
Of all water damage claims related to washing machines, more than
half are from water supply hoses that leaked or burst. Over time, most washing machine hoses, even
those that are installed properly, will eventually fail, leading to leaks or
catastrophic floods caused when the hoses burst. Failure may be caused any of several factors,
including age, installation error, poor-quality materials, and poor design.
All washer hoses, whether
reinforced rubber or braided steel, must be installed properly, inspected
regularly, and replaced before they wear out. If an inspection reveals any danger signs
(such as blisters, bulges, bubbles, cracks, crimps, kinks, unraveling, rust,
discoloration, etc.), or if leaks are present, replace the hoses and fittings
immediately. Remember that damage
and deterioration may exist on the inside of the hose or fitting and may not be
visible during an inspection.
Figure 5.
Bubbles in the water hoses.
Metropolitan Engineering, Consulting & Forensics (MECF)
Providing
Competent, Expert and Objective Investigative Engineering and Consulting
Services
P.O. Box 520
Tenafly, NJ 07670-0520
Tel.: (973) 897-8162
Fax: (973) 810-0440
E-mail:
metroforensics@gmail.com
Web pages:
https://sites.google.com/site/metropolitanforensics/
https://sites.google.com/site/metropolitanenvironmental/
https://sites.google.com/site/metroforensics3/
We are happy to announce the launch of our twitter account. Please make
sure to follow us at @MetropForensics or @metroforensics1
Metropolitan
appreciates your business.
Feel free to
recommend our services to your friends and colleagues.