FATAL BACKOVER WORKER ALERT AT CONSTRUCTION SITES
It is always very sad to see a young man working for a living
in the cold weather to die at a construction site. Please read this safety alert and ensure that
your staff implements the recommendations.
On February 15, 2014, a 26 year old male employee working as a “Swamper”
(driver apprentice) for an oil field trucking company, was fatally injured when
he was backed over by a co-worker operating a gas engine, 1-ton dually, welding
truck. The welding truck was in the process of relocating past winch truck operations
on the well site at the time of the incident.
The company was in preparation for a “rig up stage” at a new well
drill site. Just prior to the incident, the welding truck driver and the winch truck
employees of the same company met and discussed the planned work. All three employees
were aware the welding truck would be required to back up from where it was located,
and drive past the swamper and winch truck driver’s location.
The Swamper was assisting the winch truck driver in the relocation
of mud and water tanks. After the previous meeting, the winch truck driver returned
to his truck, and the Swamper assisted in horizontal rigging of the tank to winch
equipment. The welder returned to his truck to move it.
At the time of the accident the welding truck driver was
operating a truck without benefit of back- up alarm or spotter. As the welding truck
driver backed his vehicle up to the new location, the swamper positioned
himself along the storage tank being winched. The swamper stepped backward into the path of the
welding truck, the welding truck passed completely over the victim.
The decedent died of his injuries at the scene.
Cause and Significant Contributing Factors:
·
The welding truck driver arrived on site after
the morning job safety analysis (JSA) and tailgate safety meeting.
·
All three workers failed to identify the hazards
present on location.
·
There were four different diesel engines running
in the area of the incident, creating significant background noise. The diesel engine
noise and winds diminished the victim’s ability to hear the much quieter
gasoline engine of the welding truck.
·
The victim was wearing a hooded sweatshirt under
FRC coveralls, which created limited peripheral vision.
·
The victim inadvertently positioned himself in the
path of the welding truck to avoid hazards associated with the winching operation
he was assisting with.
·
The victim had his back to the driver; the driver
had his back to the victim.
·
The driver of the welding truck could not see directly
to the rear due to truck design, obstructed view created by the welding equipment
and the driver did not ask for a spotter to assist.
·
The gas engine welding truck was never equipped with
a back-up alarm.
·
The victim did not offer to be a spotter, and
the winch truck driver did not offer to be a spotter.
·
The trucking company did have a vehicle inspection
form, but it was used inconsistently.
·
The inspection form did not have a vehicle specific
format, or a back-up alarm check.
·
The winch truck driver was likely in transition of
view; he was shifting from left side mirror to right side mirror and rear window
view of winch process.
Recommendations:
·
Brief all employees on the facts and circumstances
of this fatal incident.
·
In accordance with OSHA Construction Standards, properly
equip motor vehicles used in construction environments with audible devices that
may be heard over other sounds when being backed-up.
·
Revisit safety programs and JSA information to ensure
they are applicable to OSHA standards necessary for the work to be performed.
·
Use a spotter when backing equipment near other personnel
as required.
·
Utilize high visibility outer garments.
·
Be aware of your surroundings.
·
Avoid wearing clothing or hooded garments which
limit your field of view.
·
Use of approved FRC helmet liners is preferred, as
they turn with your head.
·
Ensure that pre-tour safety meetings are conducted
to discuss the work to be performed, identifying the potential safety hazards and
implementing safe work procedures to control hazards.
·
Ensure the safety meeting information is provided
to all employees.
Preventing Backovers
A backover incident occurs when a backing vehicle strikes a
worker who is standing, walking, or kneeling behind the vehicle. These
incidents can be prevented. According to the Bureau of Labor Statistics, over
70 workers died from backover incidents in 2011. These kinds of incidents can
occur in different ways. For example:
On June 18, 2009, an employee was working inside a work
zone wearing his reflective safety vest. A dump truck operating in the work
zone backed up and struck the employee with the rear passenger side wheels. The
employee was killed. The dump truck had an audible back up alarm and operating
lights. (OSHA Inspection Number 313225377)
On June 9, 2010, an employee was standing on the ground
in front of a loading dock facing into the building while a tractor trailer was
backing into the same dock. The trailer crushed the employee between the
trailer and the dock. (OSHA Inspection Number 314460940).
The purpose of this webpage is to provide information about the
hazards of backovers; solutions that can reduce the risk or frequency of these
incidents; articles and resources; and references to existing regulations and
letters of interpretation.
How do backover incidents occur?
What can be done to prevent backover incidents?
Many solutions exist to prevent backover incidents. Drivers can
use a spotter to help them back up their vehicles. Video cameras with
in-vehicle display monitors can give drivers a view of what is behind them.
Proximity detection devices, such as radar and sonar, can alert drivers to
objects that are behind them. Tag-based systems can inform drivers when other
employees are behind the vehicle and can alert employees when they walk near a
vehicle equipped to communicate with the tag worn by the employee. On some work
sites, employers can create internal traffic control plans, which tell the
drivers where to drive and can reduce the need to back up. In some cases,
internal traffic control plans can also be used to separate employees on foot from
operating equipment.
Training is another tool to prevent backover incidents. Blind
spots behind and around vehicles are not immediately obvious to employees on
foot. By training employees on where those blind spots are and how to avoid
being in them, employers can prevent some backover incidents. One component of
this training can include putting employees who will be working around vehicles
in the driver’s seat to get a feel for where the blind spots are and what,
exactly, the drivers can see. The National Institute for Occupational Safety
and Health (NIOSH) several blind spot diagrams that can help explain what
drivers of various large trucks can see.
Vehicles Causing the Most Backover Fatalities
2005-2010+
Dump Truck
|
67
|
Semi/Tractor Trailer
|
40
|
Truck
|
30
|
Forklift
|
21
|
Garbage Truck
|
20
|
Pick-up Truck
|
16
|
Highlights
Preventing Backovers. Safety Clearinghouses.
Provides links to information relating to backover incidents in highway work
zones.
Metropolitan Engineering, Consulting &
Forensics (MECF)
Providing
Competent, Expert and Objective Investigative Engineering and Consulting
Services
P.O. Box
520
Tenafly,
NJ 07670-0520
Tel.:
(973) 897-8162
Fax:
(973) 810-0440
We are happy to announce the launch of our twitter account.
Please make sure to follow us at @MetropForensics or @metroforensics
Metropolitan
appreciates your business.
Feel
free to recommend our services to your friends and colleagues.